Skip to main content

PMS 200

PMS 200

NWCG Standards for Wildland Fire Resource Typing PMS 200

Aircraft

Crews

Equipment

Equipment, PMS 200

Dozers

Dozer Typing Standard

Requirements Type 1 Type 2 Type 3 Type 4
Net HP Range* 240 and up 150 - 250 99 - 165 50 - 110
Minimum Base Weight** 60,000 lbs. 35,000 lbs. 20,000 lbs. 10,000 lbs.
*Manufacturer’s published rated net horsepower (HP). Horsepower rating taken at the flywheel with all the engine accessories installed not counting transmission losses or anything after the flywheel.
**Manufacturer’s published base weight for dozer including equipped track width and blade configuration, equipment fluids, etc. If a published base weight is unavailable, a certified in-service weight shall be used.
Base operational weight is only used for typing. Final in-service dozer weight will be higher and include additional accessories such as winch, grapple, forestry package, etc. Final in-service dozer weight must be used when calculating hauler capacity, bridge weight limits, etc.

 

Engines

The NWCG categorizes information on fire apparatus into logical groups and provides common options often requested by fire managers. The Incident Command System (ICS) uses this system based on the equipment capability. The table below shows NWCG minimum performance requirements for structure and, wildland engine resource types. Additional information for required crew training and equipment recommendations can be found at the position catalog.

Engine Typing Standard

Types 1 and 2 are structure; Types 3-7 are wildland

Requirements Type 1 Type 2 Type 3 Type 4 Type 5 Type 6 Type 7
Tank minimum capacity (gal) 300 300 500 750 400 150 50
Pump minimum flow (gal/min) 1,000 500 150 50 50 50 10
At rated pressure (psi) 150 150 250 100 100 100 100
Hose: 2½-inch 1,200 1,000 N/A N/A N/A N/A N/A
Hose: 1½-inch 500 500 1,000 300 300 300 N/A
Hose: 1-inch N/A N/A 500 300 300 300 200
Ladders per NFPA 1901 Yes Yes N/A N/A N/A N/A N/A
Master stream 500 gal/min. Yes N/A N/A N/A N/A N/A N/A
Pump and roll N/A N/A Yes Yes Yes Yes Yes
Maximum GVWR (lb) N/A N/A N/A N/A 26,000 19,500 14,000
Personnel (minimum) 4 3 3 2 2 2 2

N/A = Not applicable
NFPA = National Fire Protection Association
GVWR = Gross Vehicle Weight Rating

Notes:

  1. All types shall meet federal, state and agency requirements for motor vehicle safety standards, including all gross vehicle weight ratings when fully loaded.
  2. Type 3 engines and tactical water tenders shall be equipped with a foam proportioner system.
  3. All water tenders and engine types 3 through 6 shall be able to prime and pump water from a 10 foot lift.
  4. Personnel shall meet the qualification requirements of NWCG Standards for Wildland Fire Position Qualifications, PMS 310-1.

Engine Resources

Tractor Plows / Dozer Plows

Tractor Plow / Dozer Plow Standard

Requirements Type 1 Type 2 Type 3 Type 4
Net HP Range* 240 and up 150 - 250 99 - 165 50 - 110
Minimum Base Weight** 60,000 lbs. 35,000 lbs. 20,000 lbs. 10,000 lbs.
*Manufacturer’s published rated net horsepower (HP). Horsepower rating taken at the flywheel with all the engine accessories installed not counting transmission losses or anything after the flywheel.
**Manufacturer’s published base weight for dozer including equipped track width and blade configuration, equipment fluids, etc. Includes published blade weight whether or not the tractor plow / dozer plow is equipped with a front blade. Does not include weight of plow. If a published base weight is unavailable, a certified in-service weight shall be used.
Base operational weight is only used for typing. Final in-service weight will be higher and include additional accessories such as plow, winch, grapple, forestry package, etc. Final in-service weight must be used when calculating hauler capacity, bridge weight limits, etc.

 

Water Tenders

The NWCG categorizes information on fire apparatus into logical groups and provides common options often requested by fire managers. The Incident Command System (ICS) uses this system based on the equipment capability. The table below shows NWCG minimum performance requirements for water tenders. Additional information for required crew training and equipment recommendations can be found at the position catalog.

Water Tender Typing Standard

Requirements Support Type 1 Support Type 2 Support Type 3 Tactical Type 1 Tactical Type 2
Tank capacity (gal) 4,000 2,500 1,000 2,000 1,000
Pump minimum flow (gal/min) 300 200 200 250 250
At rated pressure (psi) 50 50 50 150 150
Maximum refill time (minutes) 30 20 15 N/A N/A
Pump and roll N/A N/A N/A Yes Yes
Personnel (minimum) 1 1 1 2 2
N/A = Not applicable

Water Tender Resources

 

The National Wildfire Coordinating Group (NWCG) provides national leadership to enable interoperable wildland fire operations among federal, state, Tribal, territorial, and local partners. NWCG operations standards are interagency by design; they are developed with the intent of universal adoption by the member agencies. However, the decision to adopt and utilize them is made independently by the individual member agencies and communicated through their respective directives systems.

Print PDF

NWCG Latest Announcements

NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212, and Next Generation Position Task Book for Basic Faller Are Now Available

Date: April 14, 2025
Questions?  Please contact:
Hazard Tree and Tree Felling Subcommittee

The updated NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212, and NWCG Position Task Book for Basic Faller (FAL3), PMS 311-19 are now available.

The NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212 includes position standards designed to be used in conjunction with the Next Generation Position Task Book (Next Gen PTB). The Next Gen PTB for Basic Faller (FAL3) includes an evaluation guide with suggested rating elements to consider when assessing trainees.

References:

NWCG Standards For Wildland Fire Chainsaw Operations, PMS 212

NWCG Position Task Book for Basic Faller (FAL3), PMS 311-119

NWCG Basic Faller (FAL3)

RMC Memo 25-01: Summary of Updates to Safety Officer Positions

Date: April 9, 2025
Questions?  Please contact:
RMC Member Eric Fransted

The Risk Management Committee (RMC) serves as the position steward for all Safety Officer incident positions and continues to improve position standards, training, and naming conventions. The implementation of Complex Incident Management (CIM) required changes to position titles. RMC collaborated with the NWCG Incident Position Standards Committee (IPSC) to propose and implement these updates. 

References:

RMC Memo 25-01: Summary of Updates to Safety Officer Positions 

NWCG Position Catalog

Updated, NWCG Guide to Wildland Fire Origin and Cause Determination, PMS 412

Date: April 8, 2025
Questions?  Please contact:
Wildland Fire Investigation Subcommittee

PMS 412 provides guidance for wildland fire investigations. This guide outlines recommended procedures, practices, techniques, and methods to promote a systematic approach. The last update to this publication was in 2016.

References:

NWCG Guide to Wildland Fire Origin and Cause Determination PMS 412

Updated NWCG Standards for Airtanker Base Operations, PMS 508

Date: March 31, 2025
Questions?  Please contact:
Airtanker Base Operations Unit

The updated NWCG Standards for Airtanker Base Operations (SABO), PMS 508 standardizes operations and procedures at interagency airtanker bases to ensure safe, efficient, and effective operations in support of interagency goals and objectives.

References:

NWCG Standards for Airtanker Base Operations, PMS 508